- EMC Filters
- Chokes
- Resistors
- Classics
- Test Technology
- Transformers
- Current Transformers
- Power Electronics
- Vibratory Feeder Components
Choose your category...
Markets
Thyristor Power Controller
-
REOTRON MEW 700
REOTRON MEW series, single-phase, microprocessor-based, thyristor-controllers are suitable for resistive or resistive/inductive loads, especially those with a high Rcold / Rwarm coefficient. Status relays indicate unit ready and fault conditions. Depending on settings, the controller normally operates on the phase-angle principle (standard setting).
It can also be used in a burst-fire mode. Phase-angle mode the unit works as a regulator for RMS current, RMS voltage or power. Adjustment is variable. External setpoint signals can be used for controlling current, voltage and power, or potentiometers may be used instead. A serial RS232, PROFIBUS-DP field bus interface can be used for remote adjustment.
All unit settings can be made through the controller’s front-panel, using an LED display and keypad.Max ambient temp: 0...+45 (°C) Output current: 0...300 A Output voltage: 0...Ue-3 V Phase: Single phase Protection: 20 IP Supply voltage: 230...400, +/-1 V -
REOTRON MDW 700
REOTRON MDW series, three-phase, microprocessor-based thyristor controllers are suitable for resistive or resistive/inductive loads, especially those with a high Rcold / Rwarm coefficient.
Status relays indicate unit ready and fault conditions.
Depending on settings, the controller normally operates on the phase-angle principle (standard setting). It can also be used in a burst-fire mode. In the phase-angle mode the unit works as a regulator for RMS current, RMS voltage, or real power. The proportional regulation
adjustment is variable.
External setpoint signals can be used for controlling current, voltage and power, or potentiometers may be used instead. A serial RS232 or CANBUS, Device-Net, PROFIBUS-DP or EtherCat field bus interface can be used for remote adjustment. All unit settings can be made through the
controller’s front-panel, using a LED display and keypad.
Additional fan-assisted cooling is provided on units with current ratings higher than 50 A.Max ambient temp: 0...+45 (°C) Output current: 3 x 0...300 A Output voltage: 3 x 0...Ue-3 V Phase: Three phase Protection: 20 IP Supply voltage: 3 x 0...400 V -
REOTRON MDW 700 WK
A serial RS232, CANBUS, Device-Net, PROFIBUS-DP or EtherCat field bus interface can be used for remote adjustment. All unit settings can be made through the controller’s frontpanel, using a LED display and keypad.
Water cooling is provided on all units.
REOTRON MDW 700 -WK series, three-phase, microprocessor-based thyristor controllers are suitable for resistive or resistive/inductive loads, especially those with a high Rcold / Rwarm coefficient. Status relays indicate unit ready and fault conditions.
Depending on settings, the controller normally operates on the phase-angle principle (standard setting). It can also be used in a burst-fire mode. In the phase-angle mode the unit works as a regulator for RMS current, RMS voltage, or real power. The proportional regulation adjustment is variable. External setpoint signals can be used for controlling current, voltage and power or potentiometers may be used instead.
Max ambient temp: 0...+45 (°C) Output current: 3x0 A Output voltage: 3x0 V Phase: Three phase Protection: 20 IP Supply voltage: 3x0 V -
REOTRON MDZ 2000
The range of REOTRON MDZ regulators are microprocessor based units designed to control thyristors in a 6- pulse controlled bridge (B6).The units comprise control and regulating electronics and also firing pulsegeneration and the pulse output module. The MDZ 2000 can be used as a current or voltage regulator, whereby output corrections are made relative to the appropriate setpoint input. The actual set point can be derived from an external potentiometer, 0…10 VDC or a 0…20mA / 4…20mA control signal. The standard feedback value is +/- 0…40 VDC for the rectifier output voltage and +/- 0…100mA forthe current output. The MDZ 2000 replace the previous MDZ 5941 design.
Phase: 3 Protection: IP 20 Supply voltage: 3 x 400 V -
REOTRON EW 509
REOTRON EW 509 is a single-phase thyristor power regulator for load currents up to 15 A.
The control electronics are isolated from the mains voltage. Load power is controlled by means of thyristors operated in the phase-angle control mode.
The setpoint signal can be provided either by a potentiometer, or by a 0...+ 10 VDC or a 0(4)...20 mA control signal. Matching of load power to the required setpoint range is effected by internal trimmer potentiometers for Umin/Umax.
Remote control of the unit is possible by means of an enable/inhibit input. An internal control circuit compensates variations of the mains supply. The unit is mounted to a 35 mm DIN rail
according to EN 50022-35.Max ambient temp: 0 to +45 (°C) Output current: 0 to 15 A Output voltage: 0 to 400 V Phase: Single Phase Protection: 20 IP Supply voltage: 0 to 400, +6% -1 -
REOTRON EW 514
REOTRON EW 514 is a single-phase thyristor power regulator for load currents up to 6 A. The control electronics are isolated from the mains voltage. Load power is controlled by means of thyristors operated in the phase-angle control mode. The setpoint signal can be provided either by a potentiometer, or by a 0...+ 10 VDC or by a 0(4)...20 mA control signal.
Matching of load power to the required setpoint range is effected by internal trimmer potentiometers for Umin/Umax. Remote control of the unit is possible by means of an enable/inhibit input. Variation of the mains supply are compensated by an internal control circuit. The unit is mounted to a 35 mm rail to DIN EN 50 022.Max ambient temp: 0...+45 (°C) Output current: 6 A Output voltage: 0...230 V Phase: Single phase Protection: IP20 Supply voltage: 230 V